e-21 elliptical heatshrink boots are designed for glenair rectangular hiper-d backshells with large elliptical cable entries. heatshrink boots provide strain relief and environmental protection. shape-memory polymer returns to as-molded shape when heat is applied. boot lip fts adapter groove for precise ft. semi-rigid high performance elastomer resists high temperature and withstands exposure to petroleum-based fuids and fuels. also available with non-halogenated fame-retardant polyolefn for use where limited fre hazard is required. pl us t rans iti ons , c onvo luted boo ts , and ada pter s for h arsh -envi ronm ent ca ble a s sembli es u nited state s ? u nited k ingdo m ? g erma n y ? f ra n c e ? n o r di c ? i ta l y ? sp a i n ? ja p a n series 77 ?full nelson? environmental shrink boots nd series 77 full nelson shrink boot catalog has additional boot styles, technical information, installation instructions and other heatshrink products. contact glenair or go to www.glenair.com . p r e-c o ated adhesi v e selecti o n guide low smoke zero halogen (lszh) polyamide hot melt adhesive coating. bonds well to a variety of substrates. good creep resistance at elevated temperatures. excellent bond strength at low temperature. good resistance to fuels and oils. -55 c to +105c. compatible with type 1 and type 2 boot materials. high temperature epoxy adhesive coating . glenairs highest performance pre- coated adhesive. the material requires careful installation using trained operators. -75c to 150c. withstands prolonged high temperature immersion in fuels and oils. excellent peel adhesion. compatible with type 1 and type 2 boot materials. w1 r about user-installed adhesive heat-shrink boots are not watertight unless equipped with pre-coated or user- installed adhesives. when heat is applied to the boot, the adhesive melts and fxes the boot to the adapter and cable jacket to provide the necessary sealing as well as mechanical strain-relief. for maximum performance glenair recommends type u user-installed two-part epoxy adhesive which ofers reduced boot installation time and easier installation. pre-coated boots require additional care to install because the boot must be heated sufciently to activate the epoxy, at the risk of overheating the overall assembly. a single 50 ml duo syringe can coat many boots. the duo syringe can be re-capped for re-use. inexpensive mixing nozzles must be discarded after each use. n o te: glenair high-p erformance two part epoxy meets v g95343 part 15. see next page for ordering information on user-installed two part epoxy adhesive. elliptical d-subminiature heatshrink boots 770-030 mate r ial selecti o n guide type 1 high performance elastomer -75 c to +150c. semi-rigid high performance elastomer combines excellent resistance to fuels, oils and solvents with superior performance at extreme temperatures. material meets the requirements of vg95343 type 6, bsg 198-5-de, en62329-102 and sae as5258 type h. recommended for demanding applications such as military vehicles and petrochemical exploration. type 2 zero halogen polyolefn -30 c to +135c. low smoke zero halogen (lszh) polyolefn boots meet low smoke and toxicity requirements of shipboard, transit and aircraft systems. oxygen index greater than 30%, smoke index less than 20, and toxicity index under 3 per 100 grams. material meets requirements of navsea 5617649, vg95343 part 29, bsg 198-5-df, en62329-101 and sae as5258 type g. good resistance to oils, fuels and solvents. 1 2 o rdering information sample part number 770-030 1 05 r basic part number 770-030 material 1 = high performance elastomer 2 = zero halogen polyolefn boot size 05 = size 05 06 = size 06 (see next page for dimensions) adhesive lining w1 = low smoke zero halogen polyamide hot melt adhesive r = high temperature, high strength epoxy adhesive omit for boot with no adhesive lining ? 2013 glenair, inc ? 1211 air way, glendale, ca 91201 ? 818-247-6000 ? www.glenair.com ? u.s. cage code 06324 series 28 hiper-d accessories e
e-22 elliptical d-subminiature heatshrink boots 770-030 b d e a c l m h j g f k expanded recovered boot size a min b min c min d min e max f 10% g max h max j 10% k 10% l max m 10% in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm 05 1.50 38.1 2.00 50.8 .800 20.3 1.00 25.4 .375 9.53 1.062 27 1.125 28.6 .200 5.08 .060 1.52 2.29 58.2 .375 9.53 .070 1.78 06 1.80 45.7 2.50 63.5 .580 14.7 1.50 38.1 .450 11.43 1.062 27 1.637 41.6 .145 3.68 .060 1.52 3.05 77.5 .375 9.53 .070 1.78 770-030 heatsh r ink b oo t dimensi o ns 770-030 heatsh r ink b oo t identific ati o n m a r kings use r -installed b oo t adhesi v e , dispensing gun and mi x ing n o zzle high performance fexible two part thermoset epoxy provides high strength fexible bond from -55 to 150 c. 50 ml duo syringe fts standard dispensing guns. use with square green mixing nozzle sold separately. 12 hour cure time at 20 c, 1 hour at 85 c, 30 minutes at 150 c. apply to inside of boot with wooden spatula. 18 month shelf life. twin push-rod 1:1 ratio epoxy dispensing gun for use with duo syringe epoxy and mixing nozzle sold separately. durable heavy-duty plastic. gun type hand grip with ratcheting trigger to advance push-rods. 1:1 ratio mixing nozzle attaches to duo syringe with 1/2 turn and locks into place. nozzle provides consistent mixing of resin and hardener. kit consists of (12) nozzles. part number 779-001 part number 779-002 part number count per pack 779-003 12 e05 glenair a c heatshrink boots are identified with molded-in lettering. this lettering shows the boot type, boot size and orientation. position the boot so that the lipped a end is toward the adapter and the c end is toward the cable. assembly instructions are in the series 77 full nelson environmental shrink boots catalog, available at www.glenair.com. ? 2013 glenair, inc ? 1211 air way, glendale, ca 91201 ? 818-247-6000 ? www.glenair.com ? u.s. cage code 06324 series 28 hiper-d accessories e
|
